Tomasz Chmielewski schrieb: > juan--nsd82 at lavera.dnsalias.net schrieb: > >> Could anyone who has managed to install Debian on the hard disk please >> post here the results of fdisk -l, dmesg, ... ? > > This one is a 80 GB model: This one is for a 160 GB model: # fdisk -l Disk /dev/sda: 163.9 GB, 163928604672 bytes 255 heads, 63 sectors/track, 19929 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 255 2048287 82 Linux swap / Solaris /dev/sda2 256 19929 158031405 83 Linux # hdparm -I /dev/sda /dev/sda: ATA device, with non-removable media Model Number: Maxtor 6L160P0 Serial Number: L3DRVCEH Firmware Revision: BAJ41G20 Standards: Used: ATA/ATAPI-7 T13 1532D revision 0 Supported: 7 6 5 4 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 320173056 device size with M = 1024*1024: 156334 MBytes device size with M = 1000*1000: 163928 MBytes (163 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 0 Advanced power management level: unknown setting (0x0000) Recommended acoustic management value: 192, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_VERIFY command * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE Advanced Power Management feature set SET_MAX security extension * Automatic Acoustic Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test Media Card Pass-Through * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * URG for READ_STREAM[_DMA]_EXT * URG for WRITE_STREAM[_DMA]_EXT * SMART Command Transport (SCT) feature set * SCT Data Tables (AC5) Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase HW reset results: CBLID- above Vih Device num = 0 determined by the jumper Checksum: correct # cat /var/log/dmesg Linux version 2.6.20 (build at syn4) (gcc version 4.1.1) #60 PREEMPT Wed Feb 21 12:18:31 CET 2007 CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE), cr=0000397f Machine: Freecom FSG-3 Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 16384 DMA zone: 128 pages used for memmap DMA zone: 0 pages reserved DMA zone: 16256 pages, LIFO batch:3 Normal zone: 0 pages used for memmap CPU0: D VIVT undefined 5 cache CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Built 1 zonelists. Total pages: 16256 Kernel command line: console=ttyS0,115200 mem=64M panic=5 PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 62208KB available (2388K code, 146K data, 136K init) Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 IXP4xx: Using 16MiB expansion bus window size PCI: IXP4xx is host PCI: IXP4xx Using direct access for memory space PCI: bus0: Fast back to back transfers disabled dmabounce: registered device 0000:00:0c.0 on pci bus dmabounce: registered device 0000:00:0e.0 on pci bus dmabounce: registered device 0000:00:0e.1 on pci bus dmabounce: registered device 0000:00:0e.2 on pci bus SCSI subsystem initialized libata version 2.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale sata_via 0000:00:0c.0: version 2.0 PCI: enabling device 0000:00:0c.0 (0000 -> 0001) sata_via 0000:00:0c.0: routed to hard irq line 6 ata1: SATA max UDMA/133 cmd 0x1420 ctl 0x142A bmdma 0x1400 irq 22 ata2: SATA max UDMA/133 cmd 0x1430 ctl 0x143A bmdma 0x1408 irq 22 ata3: PATA max UDMA/133 cmd 0x1440 ctl 0x144A bmdma 0x1410 irq 22 scsi0 : sata_via ata1: SATA link down (SStatus 0 SControl 310) ATA: abnormal status 0x7F on port 0x1427 scsi1 : sata_via ata2: SATA link down (SStatus 0 SControl 310) ATA: abnormal status 0x7F on port 0x1437 scsi2 : sata_via ata3.00: ATA-7, max UDMA/133, 320173056 sectors: LBA48 ata3.00: ata3: dev 0 multi count 0 ata3.00: configured for UDMA/33 scsi 2:0:0:0: Direct-Access ATA Maxtor 6L160P0 BAJ4 PQ: 0 ANSI: 5 SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sd 2:0:0:0: Attached scsi disk sda NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank IXP4XX-Flash.0: Found an alias at 0x400000 for the chip at 0x0 IXP4XX-Flash.0: Found an alias at 0x800000 for the chip at 0x0 IXP4XX-Flash.0: Found an alias at 0xc00000 for the chip at 0x0 Intel/Sharp Extended Query Table at 0x0031 Using buffer write method cfi_cmdset_0001: Erase suspend on write enabled erase region 0: offset=0x0,size=0x20000,blocks=32 Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0x3e0000 7 RedBoot partitions found on MTD device IXP4XX-Flash.0 Creating 7 MTD partitions on "IXP4XX-Flash.0": 0x00000000-0x00040000 : "RedBoot" 0x00040000-0x00080000 : "unallocated" 0x00080000-0x00200000 : "kern1" 0x00200000-0x00380000 : "kern2" 0x00380000-0x003c0000 : "unallocated" 0x003c0000-0x003e0000 : "RedBoot config" 0x003e0000-0x00400000 : "FIS directory" PCI: enabling device 0000:00:0e.2 (0140 -> 0142) ehci_hcd 0000:00:0e.2: EHCI Host Controller ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0e.2: irq 23, io mem 0x48002000 ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) PCI: enabling device 0000:00:0e.0 (0140 -> 0142) ohci_hcd 0000:00:0e.0: OHCI Host Controller ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0e.0: irq 23, io mem 0x48000000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected PCI: enabling device 0000:00:0e.1 (0140 -> 0142) ohci_hcd 0000:00:0e.1: OHCI Host Controller ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:0e.1: irq 23, io mem 0x48001000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 XScale DSP coprocessor detected. drivers/rtc/hctosys.c: unable to open rtc device (rtc0) Time: OSTS clocksource has been installed. Freeing init memory: 136K usb 3-1: new full speed USB device using ohci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. BUG: at arch/arm/mm/consistent.c:363 dma_free_coherent() kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. IXP4XX NPE driver Version 0.3.0 initialized IXP4XX Q Manager 0.2.1 initialized. ixp4xx_mac driver 0.3.1: eth0 on NPE-B with PHY[5] initialized ixp4xx_mac driver 0.3.1: eth1 on NPE-C with PHY[4] initialized ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/none/1.1.2.2 loaded HiSax: Linux Driver for passive ISDN cards HiSax: Version 3.5 (module) HiSax: Layer1 Revision 2.46.2.5 HiSax: Layer2 Revision 2.30.2.4 HiSax: TeiMgr Revision 2.20.2.3 HiSax: Layer3 Revision 2.22.2.3 HiSax: LinkLayer Revision 2.59.2.4 HFC-S USB: driver module revision 2.3.2.13 date 2006/02/17 loaded, (debug=-1) HFC-S USB: probing interface(0) actalt(0) minor(0) hfc_usb: probe of 3-1:1.0 failed with error -5 HFC-S USB: probing interface(1) actalt(0) minor(0) HFC-S USB: detected "Billion tiny USB ISDN TA 128" HiSax: Card 1 Protocol EDSS1 Id=hfc_usb0 (0) HiSax: DSS1 Rev. 2.32.2.3 HiSax: 2 channels added HiSax: MAX_WAITING_CALLS added HFC-S USB: starting intr IN fifo:5 HFC-S USB: starting intr IN fifo:1 HFC-S USB: starting intr IN fifo:3 HFC-S USB: starting ISO-chain for Fifo 4 HFC-S USB: starting ISO-chain for Fifo 0 HFC-S USB: starting ISO-chain for Fifo 2 usbcore: registered new interface driver hfc_usb swapped image found Image loaded to NPE-B Func:0, Rel: 2:1, Status: 82c00000 swapped image found Image loaded to NPE-C Func:5, Rel: 2:1, Status: 82c00000 Adding 2048276k swap on /dev/sda1. Priority:-1 extents:1 across:2048276k EXT3 FS on sda2, internal journal loop: loaded (max 8 devices) isl1208 0-006f: chip found, driver version 0.2 isl1208 0-006f: rtc core: registered isl1208 as rtc0 hwmon-vid: Unknown VRM version of your CPU eth0: link up, 100Mbps, full-duplex, lpa 0x05E1 Link of eth0 is full-duplex eth1: link up, 100Mbps, full-duplex, lpa 0x41E1 Link of eth1 is full-duplex PPP generic driver version 2.4.2 hwmon-vid: requested unknown VRM version -- Tomasz Chmielewski http://wpkg.org |