[debian-non-standard] Problems installing debian on FSG-3 (boots from flash, but cannot see internal disk)

Tomasz Chmielewski mangoo at wpkg.org
Sat Jan 26 11:11:20 CET 2008


juan--nsd82 at lavera.dnsalias.net schrieb:

> Could anyone who has managed to install Debian on the hard disk please 
> post here the results of fdisk -l, dmesg, ... ?

This one is a 80 GB model:

# fdisk -l

Disk /dev/sda: 82.3 GB, 82348277760 bytes
255 heads, 63 sectors/track, 10011 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

    Device Boot      Start         End      Blocks   Id  System
/dev/sda1               1         255     2048287   82  Linux swap / Solaris
/dev/sda2             256       10011    78365070   83  Linux


# hdparm -I /dev/sda

/dev/sda:

ATA device, with non-removable media
powers-up in standby; SET FEATURES subcmd spins-up.
         Model Number:       HDS728080PLAT20
         Serial Number:      PFD215S6R9WWBM
         Firmware Revision:  PF2OA21B
Standards:
         Used: ATA/ATAPI-7 T13 1532D revision 1
         Supported: 7 6 5 4
Configuration:
         Logical         max     current
         cylinders       16383   16383
         heads           16      16
         sectors/track   63      63
         --
         CHS current addressable sectors:   16514064
         LBA    user addressable sectors:  160836480
         LBA48  user addressable sectors:  160836480
         device size with M = 1024*1024:       78533 MBytes
         device size with M = 1000*1000:       82348 MBytes (82 GB)
Capabilities:
         LBA, IORDY(can be disabled)
         Standby timer values: spec'd by Standard, no device specific 
minimum
         R/W multiple sector transfer: Max = 16  Current = 0
         Advanced power management level: unknown setting (0x0000)
         Recommended acoustic management value: 128, current value: 254
         DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 udma6
              Cycle time: min=120ns recommended=120ns
         PIO: pio0 pio1 pio2 pio3 pio4
              Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
         Enabled Supported:
            *    SMART feature set
                 Security Mode feature set
            *    Power Management feature set
            *    Write cache
            *    Look-ahead
            *    Host Protected Area feature set
            *    WRITE_BUFFER command
            *    READ_BUFFER command
            *    DOWNLOAD_MICROCODE
                 Advanced Power Management feature set
                 Power-Up In Standby feature set
                 SET_FEATURES required to spinup after power up
                 Address Offset Reserved Area Boot
                 SET_MAX security extension
                 Automatic Acoustic Management feature set
            *    48-bit Address feature set
            *    Device Configuration Overlay feature set
            *    Mandatory FLUSH_CACHE
            *    FLUSH_CACHE_EXT
            *    SMART error logging
            *    SMART self-test
                 Media Card Pass-Through
            *    General Purpose Logging feature set
            *    64-bit World wide name
            *    URG for READ_STREAM[_DMA]_EXT
            *    URG for WRITE_STREAM[_DMA]_EXT
Security:
         Master password revision code = 65534
                 supported
         not     enabled
         not     locked
         not     frozen
         not     expired: security count
         not     supported: enhanced erase
         44min for SECURITY ERASE UNIT.
HW reset results:
         CBLID- above Vih
         Device num = 0 determined by the jumper
Checksum: correct



dmesg:


Linux version 2.6.20 (build at syn4) (gcc version 4.1.1) #60 PREEMPT Wed 
Feb 21 12:18:31 CET 2007
CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE), cr=0000397f
Machine: Freecom FSG-3
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
   DMA zone: 128 pages used for memmap
   DMA zone: 0 pages reserved
   DMA zone: 16256 pages, LIFO batch:3
   Normal zone: 0 pages used for memmap
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists.  Total pages: 16256
Kernel command line:  console=ttyS0,115200 mem=64M panic=5
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 62208KB available (2388K code, 146K data, 136K init)
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using direct access for memory space
PCI: bus0: Fast back to back transfers disabled
dmabounce: registered device 0000:00:0c.0 on pci bus
dmabounce: registered device 0000:00:0e.0 on pci bus
dmabounce: registered device 0000:00:0e.1 on pci bus
dmabounce: registered device 0000:00:0e.2 on pci bus
SCSI subsystem initialized
libata version 2.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
sata_via 0000:00:0c.0: version 2.0
PCI: enabling device 0000:00:0c.0 (0000 -> 0001)
sata_via 0000:00:0c.0: routed to hard irq line 6
ata1: SATA max UDMA/133 cmd 0x1420 ctl 0x142A bmdma 0x1400 irq 22
ata2: SATA max UDMA/133 cmd 0x1430 ctl 0x143A bmdma 0x1408 irq 22
ata3: PATA max UDMA/133 cmd 0x1440 ctl 0x144A bmdma 0x1410 irq 22
scsi0 : sata_via
ata1: SATA link down (SStatus 0 SControl 310)
ATA: abnormal status 0x7F on port 0x1427
scsi1 : sata_via
ata2: SATA link down (SStatus 0 SControl 310)
ATA: abnormal status 0x7F on port 0x1437
scsi2 : sata_via
ata3.00: ATA-7, max UDMA/133, 160836480 sectors: LBA48
ata3.00: ata3: dev 0 multi count 0
ata3.00: configured for UDMA/33
scsi 2:0:0:0: Direct-Access     ATA      HDS728080PLAT20  PF2O PQ: 0 ANSI: 5
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sda: sda1 sda2
sd 2:0:0:0: Attached scsi disk sda
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
IXP4XX-Flash.0: Found an alias at 0x400000 for the chip at 0x0
IXP4XX-Flash.0: Found an alias at 0x800000 for the chip at 0x0
IXP4XX-Flash.0: Found an alias at 0xc00000 for the chip at 0x0
  Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=32
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0x3e0000
7 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 7 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00080000 : "unallocated"
0x00080000-0x00200000 : "kern1"
0x00200000-0x00380000 : "kern2"
0x00380000-0x003c0000 : "unallocated"
0x003c0000-0x003e0000 : "RedBoot config"
0x003e0000-0x00400000 : "FIS directory"
PCI: enabling device 0000:00:0e.2 (0140 -> 0142)
ehci_hcd 0000:00:0e.2: EHCI Host Controller
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: irq 23, io mem 0x48002000
ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: enabling device 0000:00:0e.0 (0140 -> 0142)
ohci_hcd 0000:00:0e.0: OHCI Host Controller
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0e.0: irq 23, io mem 0x48000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: enabling device 0000:00:0e.1 (0140 -> 0142)
ohci_hcd 0000:00:0e.1: OHCI Host Controller
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0e.1: irq 23, io mem 0x48001000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
XScale DSP coprocessor detected.
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Time: OSTS clocksource has been installed.
Freeing init memory: 136K
usb 3-2: new full speed USB device using ohci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
IXP4XX NPE driver Version 0.3.0 initialized
IXP4XX Q Manager 0.2.1 initialized.
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/none/1.1.2.2 loaded
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
HFC-S USB: driver module revision 2.3.2.13 date 2006/02/17 loaded, 
(debug=-1)
HFC-S USB: probing interface(0) actalt(0) minor(0)
hfc_usb: probe of 3-2:1.0 failed with error -5
HFC-S USB: probing interface(1) actalt(0) minor(0)
HFC-S USB: detected "Billion tiny USB ISDN TA 128"
ixp4xx_mac driver 0.3.1: eth0 on NPE-B with PHY[5] initialized
ixp4xx_mac driver 0.3.1: eth1 on NPE-C with PHY[4] initialized
HiSax: Card 1 Protocol EDSS1 Id=hfc_usb0 (0)
HiSax: DSS1 Rev. 2.32.2.3
HiSax: 2 channels added
HiSax: MAX_WAITING_CALLS added
HFC-S USB: starting intr IN fifo:5
HFC-S USB: starting intr IN fifo:1
HFC-S USB: starting intr IN fifo:3
HFC-S USB: starting ISO-chain for Fifo 4
HFC-S USB: starting ISO-chain for Fifo 0
HFC-S USB: starting ISO-chain for Fifo 2
usbcore: registered new interface driver hfc_usb
swapped image found
Image loaded to NPE-B Func:0, Rel: 2:1, Status: 82c00000
swapped image found
Image loaded to NPE-C Func:5, Rel: 2:1, Status: 82c00000
Adding 2048276k swap on /dev/sda1.  Priority:-1 extents:1 across:2048276k
EXT3 FS on sda2, internal journal
loop: loaded (max 8 devices)
ds1307 0-0068: rtc core: registered ds1307 as rtc0
hwmon-vid: Unknown VRM version of your CPU
eth0: link up, 100Mbps, full-duplex, lpa 0x05E1
Link of eth0 is full-duplex
eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
Link of eth1 is full-duplex
PPP generic driver version 2.4.2
NET: Registered protocol family 24
hwmon-vid: requested unknown VRM version
ip_tables: (C) 2000-2006 Netfilter Core Team



-- 
Tomasz Chmielewski
http://wpkg.org



More information about the debian-non-standard mailing list