[stgt] Reply:Fw:Reply:Reply:Re: attached devices exported by tgt not oprational
席智勇
xizhiyong18 at 163.com
Tue Sep 23 10:31:38 CEST 2014
in tgt, i found that, when a lun is created or destroyed, ASC_REPORTED_LUNS_DATA_HAS_CHANGED was add to I_T by
ua_sense_add(), except for command REPORT LUN,
in IET, i do not find the same program logic,
is this the reason why i met the problem when i using tgt, but not when IET？
At 2014-09-22 20:23:27, "席智勇" <xizhiyong18 at 163.com> wrote:
>may you give some advise to me about the problem report by me.
>
>-------- Forwarding messages --------
>From: "席智勇" <xizhiyong18 at 163.com>
>Date: 2014-09-22 03:29:51
>To: "席智勇" <xizhiyong18 at 163.com>
>Cc: "ronnie sahlberg" <ronniesahlberg at gmail.com>,stgt at vger.kernel.org
>Subject: Reply:Reply:Re: attached devices exported by tgt not oprational
>from the syslog of the initiator side, it seams the sd_revalide_disk was trigged more
>than once, and it succeed first time, when logged "sd 7:0:0:4: [sdf] Attached SCSI disk",
>i don't when and where the sd_revalidate was called again, and it failed when send SCSI
>command TEST_UNIT_READ and RRAD_CAPACITY.
>
>
>
>At 2014-09-11 11:35:57, "席智勇" <xizhiyong18 at 163.com> wrote:
>>first of all, thanks for your reply.
>>in my program, it will use 128 LUNS at the most each target, so LUNS id will
>>not outnumber 255.
>>
>>here is some syslog when the problem occur. you can search [sdf] to find some
>>info, like "[sdf] READ CAPACITY(16) failed" or "[sdf] Unit Not Ready", and "sdf: detected capacity change from 9664266240 to 0",
>>"Sense Key : Illegal Request [current]", "Add. Sense: Logical unit not supported"
>>------------------------------------------------------------------------------------------
>>
>>#:~/tgt_debug$ cat syslog |grep -C 1 -e "sdf\|sd 7:0:0:4"
>>
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.426520] sd 7:0:0:4: [sdf] 18875520 512-byte logical blocks: (9.66 GB/9.00 GiB)
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.426629] sd 7:0:0:3: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>>--
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427236] sd 7:0:0:5: Attached scsi generic sg12 type 0
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427409] sd 7:0:0:4: [sdf] Write Protect is off
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427414] sd 7:0:0:4: [sdf] Mode Sense: 69 00 00 08
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427545] sd 7:0:0:5: [sdg] 2097280 512-byte logical blocks: (1.07 GB/1.00 GiB)
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427875] sd 7:0:0:4: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427926] scsi 7:0:0:7: Direct-Access IET VIRTUAL-DISK 0001 PQ: 0 ANSI: 5
>>--
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.443681] sd 7:0:0:5: [sdg] Attached SCSI disk
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.458714] sdf: unknown partition table
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.460786] sd 7:0:0:4: [sdf] Attached SCSI disk
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.476316] sdh: unknown partition table
>>--
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.701790] Add. Sense: Reported luns data has changed
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703810] sd 7:0:0:4: [sdf] Unit Not Ready
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703814] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703815] Sense Key : Unit Attention [current]
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703818] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703821] Add. Sense: Reported luns data has changed
>>--
>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.336478] Add. Sense: Reported luns data has changed
>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338547] sd 7:0:0:4: [sdf] Unit Not Ready
>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338552] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338554] Sense Key : Unit Attention [current]
>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338558] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338561] Add. Sense: Reported luns data has changed
>>--
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752462] sdd: detected capacity change from 1073807360 to 0
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752987] sd 7:0:0:4: [sdf] Unit Not Ready
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752990] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752991] Sense Key : Unit Attention [current]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752994] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752997] Add. Sense: Reported luns data has changed
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753254] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments.
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753472] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments.
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753655] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments.
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753666] sd 7:0:0:4: [sdf] READ CAPACITY(16) failed
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753672] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753674] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753676] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753677] Sense Key : Unit Attention [current]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753680] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753682] Add. Sense: Reported luns data has changed
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753883] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments.
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754075] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments.
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754275] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments.
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754286] sd 7:0:0:4: [sdf] READ CAPACITY failed
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754291] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754292] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754295] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754296] Sense Key : Unit Attention [current]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754299] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754301] Add. Sense: Reported luns data has changed
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.756150] sdf: detected capacity change from 9664266240 to 0
>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.756639] sd 7:0:0:5: [sdg] Unit Not Ready
>>--
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.925588] scsi 3:0:0:21: Direct-Access IET VIRTUAL-DISK 0001 PQ: 0 ANSI: 5
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.925959] sd 7:0:0:4: [sdf] 18875520 512-byte logical blocks: (9.66 GB/9.00 GiB)
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.926000] sd 3:0:0:21: Attached scsi generic sg59 type 0
>>--
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.927749] sd 3:0:0:22: [sdbc] 18875520 512-byte logical blocks: (9.66 GB/9.00 GiB)
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.927762] sdf: detected capacity change from 0 to 9664266240
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.927843] scsi 3:0:0:23: Direct-Access IET VIRTUAL-DISK 0001 PQ: 0 ANSI: 5
>>--
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.191743] Add. Sense: Reported luns data has changed
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195776] sd 7:0:0:4: [sdf] Unit Not Ready
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195779] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195780] Sense Key : Unit Attention [current]
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195784] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195786] Add. Sense: Reported luns data has changed
>>--
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.592427] sd 7:0:0:39: [sdbx] Mode Sense: 69 00 00 08
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.592809] sd 7:0:0:40: Attached scsi generic sg82 type 0
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.594486] sd 7:0:0:39: [sdbx] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.594696] sd 7:0:0:40: [sdby] 18875520 512-byte logical blocks: (9.66 GB/9.00 GiB)
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.595825] sd 7:0:0:40: [sdby] Write Protect is off
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.595831] sd 7:0:0:40: [sdby] Mode Sense: 69 00 00 08
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.596261] sd 7:0:0:40: [sdby] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.605687] sdbx: unknown partition table
>>--
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.610455] sd 7:0:0:39: [sdbx] Attached SCSI disk
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.613057] sd 7:0:0:40: [sdby] Attached SCSI disk
>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.617631] sd 3:0:0:13: [sdaf] Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments.
>>--
>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.432518] md113: unknown partition table
>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.662356] sd 7:0:0:4: [sdf] Synchronizing SCSI cache
>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663163] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663167] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663170] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663172] Sense Key : Illegal Request [current]
>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663175] sd 7:0:0:4: [sdf]
>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663178] Add. Sense: Logical unit not supported
>>
>>
>>At 2014-09-11 02:21:59, "ronnie sahlberg" <ronniesahlberg at gmail.com> wrote:
>>>When you say "many devices" exactly how many are you referring to?
>>>Can you check if this problem you have only occur when you go from 255
>>>LUNs to something higher?
>>>
>>>
>>>The default LUN addressing scheme only allows LUNs numbered 0 to 255.
>>>To go to higher LUN numbers, which TGTD supports, doe require that you
>>>switch to a different addressing format
>>>and it may be that your initiator can not handle those other modes.
>>>
>>>Often it might look like you have LUNs 0-255 and then there is a jump
>>>to the next LUN which has the number 16640 if the initiator can not
>>>handle addressing modes properly.
>>>
>>>
>>>I do not know how IET does the LUN numbering.
>>>
>>>If you can collect a wireshark trace of iscsiadm --login from both
>>>STGT and IET then I can take a quick look and see if that is the issue
>>>you are facing.
>>>
>>>
>>>
>>>regards
>>>ronnie sahlberg
>>>
>>>
>>>On Mon, Sep 1, 2014 at 11:00 PM, 席智勇 <xizhiyong18 at 163.com> wrote:
>>>>
>>>> when i export many block device by tgt , in one single target , this means many exported lun in one target, to another
>>>> machine by iscsi。
>>>>
>>>> in another machine , attach the devices by open-iscsi。when i wait the
>>>> size of the device attached change from 0 to correct size， i create raid1 with two devices by mdadm。at this time, mdadm report like
>>>> "/dev/sdem is not suitable for this array.", i read the code of mdadm ,that because it cannot open the device。sometime it even report
>>>> "failed to open /dev/** after earlier success - aborting "。
>>>>
>>>> i do not know whether it's because i used the device when it's not ready yet, or the problem of tgt。
>>>>
>>>> all the above said happened when many target lun(tgt) created at the same
>>>> time concurrently。it do not happen in nomal time. when i change tgt to iet, it
>>>> do not happen either。
>>>>
>>>>
>>>>
>>>> tgt version: 1.0.48
>>>>
>>>> open-iscsi version:iscsiadm version 2.0-873
>>>>
>>>> linux system: Linux 3.10.40-amd64 GNU/Linux
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> -------------
>>>>
>>>> Zhiyong Xi
More information about the stgt
mailing list