[debian-non-standard] segmentation faults and bus errors - abandoned all hope

Tomasz Orłowski t.orlowski at wsisiz.edu.pl
Sun Feb 24 21:23:42 CET 2008


Refering to my previous mail.......

I've found only one old post with problems similar to mine, and I see
that you Tomasz posted something in this thread too.
Please take a look what "astudent" wrote here -->
http://wl500g.info/showthread.php?t=6339&highlight=segmentation

He suggested problems with memory. I don't know how to obtain values
showed by nvram in Debian, so I quickly flashed my 500gP with old
Whiterussian, and did this:

root at OpenWrt:/# nvram show|grep -i ram
os_ram_addr=80001000
sdram_config=0x0062
sdram_refresh=0x0000
sdram_ncdl=0x10309
wl_frameburst=0
sdram_init=0x0009
dl_ram_addr=a0001000
size: 8752 bytes (24016 left)

I've found also here:
http://wl500g.info/showthread.php?t=10183&highlight=nvram
..that original values for WL-500gP should be like those:

sdram_init=0x000b
sdram_ncdl=0x207

I'm curious what are your settings.
I'm a little bit scared to set it, smells like fantastic chance of
bricking the box ;o) but I think I'll riks it, because I do not have any
other ideas :(

Tomasz Orlowski


Tomasz Orłowski napisał(a):
> Thanks Tomasz for quick answer.
>
> Paradoxically latest rev 10517 gives me bigger probability to have
> successful boot :oP
>
> I've attached 3 full serial console logs:
> 2 fails + 1 success (gosh it really took me some time to get this one ;O) )
>
>
> Thanks
>
> PS: I've tried it with 2 USB Sticks and 2,5" disk with IDE2USB
> connector, so I think it is not storage issue.
>
>
>
>
> fail nr1:
> ---------------------------------------------------------------------------------------
> CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
> Build Date: ¤T 12¤ë 14 15:54:18 CST 2005 (root at localhost.localdomain)
> Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
>
> Initializing Arena
> Initializing Devices.
> et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
> rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
> CPU type 0x29006: 264MHz
> Total memory: 33554432 KBytes
>
> Total memory used by CFE:  0x80800000 - 0x8089B590 (636304)
> Initialized Data:          0x80831700 - 0x80833DE0 (9952)
> BSS Area:                  0x80833DE0 - 0x80835590 (6064)
> Local Heap:                0x80835590 - 0x80899590 (409600)
> Stack Area:                0x80899590 - 0x8089B590 (8192)
> Text (code) segment:       0x80800000 - 0x80831700 (202496)
> Boot area (physical):      0x0089C000 - 0x008DC000
> Relocation Factor:         I:00000000 - D:00000000
>
> Device eth0:  hwaddr 00-17-31-DC-05-70, ipaddr 192.168.1.1, mask
> 255.255.255.0
>         gateway not set, nameserver not set
> Null Rescue Flag.
> Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
> Loading: .. 3740 bytes read
> Entry at 0x80001000
> Closing network.
> Starting program at 0x80001000
> Linux version 2.6.19.2 (tch at tomek) (gcc version 4.1.2) #9 Tue Apr 3
> 21:30:54 CEST 2007
> CPU revision is: 00029006
> ssb: Sonics Silicon Backplane found on address 0x18000000
> Determined physical RAM map:
>  memory: 02000000 @ 00000000 (usable)
> Initrd not found or empty - disabling initrd
> Built 1 zonelists.  Total pages: 8128
> Kernel command line: root=/dev/sda1 rootdelay=10 console=ttyS0,115200
> Primary instruction cache 16kB, physically tagged, 2-way, linesize 16
> bytes.
> Primary data cache 16kB, 2-way, linesize 16 bytes.
> Synthesized TLB refill handler (19 instructions).
> Synthesized TLB load handler fastpath (31 instructions).
> Synthesized TLB store handler fastpath (31 instructions).
> Synthesized TLB modify handler fastpath (30 instructions).
> PID hash table entries: 128 (order: 7, 512 bytes)
> Using 132.000 MHz high precision timer.
> Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
> Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
> Memory: 29776k/32768k available (2117k kernel code, 2992k reserved,
> 326k data, 120k init, 0k highmem)
> Mount-cache hash table entries: 512
> Checking for 'wait' instruction...  unavailable.
> NET: Registered protocol family 16
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> PCI: fixing up bridge
> PCI: Fixing up device 0000:00:00.0
> NET: Registered protocol family 2
> IP route cache hash table entries: 256 (order: -2, 1024 bytes)
> TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> TCP bind hash table entries: 512 (order: -1, 2048 bytes)
> TCP: Hash tables configured (established 1024 bind 512)
> TCP reno registered
> JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
> io scheduler noop registered
> io scheduler deadline registered (default)
> Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
> serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
> serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
> b44.c:v1.01 (Jun 16, 2006)
> eth0: Broadcom 10/100BaseT Ethernet 00:17:31:dc:05:70
> eth1: Broadcom 10/100BaseT Ethernet 40:10:18:00:00:2d
> flash init: 0x1c000000 0x02000000
> Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
>  Amd/Fujitsu Extended Query Table at 0x0040
> Physically mapped flash: CFI does not contain boot bank location.
> Assuming top.
> number of CFI chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> Flash device: 0x800000 at 0x1fc00000
> bootloader size: 262144
> Physically mapped flash: Filesystem type: jffs2
> Updating TRX offsets and length:
> old trx = [0x0000001c, 0x000008f0, 0x000e0000], len=0x00101000
> crc32=0x039d55c8
> new trx = [0x0000001c, 0x000008f0, 0x000e0000], len=0x000e0000
> crc32=0xf27087a7
> Done
> Creating 4 MTD partitions on "Physically mapped flash":
> 0x00000000-0x00040000 : "cfe"
> 0x00040000-0x007f0000 : "linux"
> 0x00120000-0x007f0000 : "rootfs"
> 0x007f0000-0x00800000 : "nvram"
> PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
> PCI: Fixing up device 0000:00:03.2
> ehci_hcd 0000:00:03.2: EHCI Host Controller
> ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:03.2: irq 6, io mem 0x40000000
> ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 4 ports detected
> USB Universal Host Controller Interface driver v3.0
> PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.0
> uhci_hcd 0000:00:03.0: UHCI Host Controller
> uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.1
> uhci_hcd 0000:00:03.1: UHCI Host Controller
> uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> usb 1-2: new high speed USB device using ehci_hcd and address 2
> Initializing USB Mass Storage driver...
> usb 1-2: configuration #1 chosen from 1 choice
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> ip_conntrack version 2.4 (256 buckets, 2048 max) - 240 bytes per conntrack
> ip_tables: (C) 2000-2006 Netfilter Core Team
> TCP cubic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> 802.1Q VLAN Support v1.8 Ben Greear <greearb at candelatech.com>
> All bugs added by David S. Miller <davem at redhat.com>
> Waiting 10sec before mounting root device...
> Time: MIPS clocksource has been installed.
> scsi 0:0:0:0: Direct-Access     TOSHIBA  MK1016GAP        U1.1 PQ: 0
> ANSI: 0 CCS
> SCSI device sda: 19640880 512-byte hdwr sectors (10056 MB)
> sda: Write Protect is off
> sda: assuming drive cache: write through
> SCSI device sda: 19640880 512-byte hdwr sectors (10056 MB)
> sda: Write Protect is off
> sda: assuming drive cache: write through
>  sda: sda1 sda2
> sd 0:0:0:0: Attached scsi disk sda
> EXT3-fs: INFO: recovery required on readonly filesystem.
> EXT3-fs: write access will be enabled during recovery.
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 120k freed
> Algorithmics/MIPS FPU Emulator v1.5
> INIT: version 2.86 booting
> /etc/init.d/rc: line 77:   133 Segmentation fault      $@
> /etc/init.d/rc: line 77:   149 Segmentation fault      $@
> /etc/rcS.d/S02mountkernfs.sh: line 22:   160 Bus error             
> grep -E -qs "sysfs\$" /proc/filesystems
> /lib/init/mount-functions.sh: line 34:   162 Bus error             
> grep -E -qs "$1\$" /proc/filesystems
> /lib/init/mount-functions.sh: line 34:   163 Bus error             
> grep -E -qs "$2\$" /proc/filesystems
> * Filesystem types 'usbfs' and 'usbdevfs' are not supported. Skipping
> mount.
> /etc/init.d/rc: line 77:   152 Segmentation fault      $@
> /etc/rcS.d/S03udev: line 154:   176 Bus error               grep -q
> '[[:space:]]tmpfs$' /proc/filesystems
> * udev requires tmpfs support, not started.
>  failed!
> /etc/init.d/rc: line 77:   174 Segmentation fault      $@
> * Files under mount point '/dev/shm' will be hidden.
> /lib/init/mount-functions.sh: line 34:   199 Bus error             
> grep -E -qs "$1\$" /proc/filesystems
> /lib/init/mount-functions.sh: line 34:   200 Bus error             
> grep -E -qs "$2\$" /proc/filesystems
> * Filesystem type 'devpts' is not supported. Skipping mount.
> /etc/init.d/rc: line 77:   189 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   209 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /etc/init.d/rc: line 77:   208 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   214 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /etc/rcS.d/S10checkroot.sh: line 24:   217 Segmentation fault      ( [
> "$PASS" != 0 ] && [ "$PASS" != "" ] )
> /etc/rcS.d/S10checkroot.sh: line 24:   218 Segmentation fault      ( [
> "$FSTYPE" = "nfs" ] || [ "$FSTYPE" = "nfs4" ] )
> Activating swap:.
> /etc/rcS.d/S10checkroot.sh: line 24:   224 Segmentation fault    
> which on_ac_power >/dev/null 2>&1
> EXT3 FS on sda1, internal journal
> /etc/init.d/rc: line 77:   213 Segmentation fault      $@
> Setting the system clock..
> Cannot access the Hardware Clock via any known method.
> Use the --debug option to see the details of our search for an access
> method.
> System Clock set. Local time: Sat Jan  1 00:00:19 UTC 2000.
> /etc/init.d/rc: line 77:   235 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   242 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /lib/init/mount-functions.sh: line 23:   246 Segmentation fault    
> which selinuxenabled >/dev/null 2>&1
> /etc/rcS.d/S12mtab.sh: line 39:   248 Bus error               grep -E
> -sq "^([^ ]+) +$2 +" /etc/mtab </dev/null
> /etc/rcS.d/S12mtab.sh: line 39:   251 Bus error               grep -E
> -sq "^([^ ]+) +$2 +" /etc/mtab </dev/null
> /etc/rcS.d/S12mtab.sh: line 66:   253 Bus error               grep -E
> -qs "sysfs\$" /proc/filesystems
> /etc/rcS.d/S12mtab.sh: line 39:   257 Bus error               grep -E
> -sq "^([^ ]+) +$2 +" /etc/mtab </dev/null
> /etc/rcS.d/S12mtab.sh: line 39:   261 Bus error               grep -E
> -sq "^([^ ]+) +$2 +" /etc/mtab </dev/null
> /etc/rcS.d/S12mtab.sh: line 39:   264 Bus error               grep -E
> -sq "^([^ ]+) +$2 +" /etc/mtab </dev/null
> /etc/rcS.d/S12mtab.sh: line 39:   267 Bus error               grep -E
> -sq "^([^ ]+) +$2 +" /etc/mtab </dev/null
> /etc/rcS.d/S12mtab.sh: line 39:   270 Bus error               grep -E
> -sq "^([^ ]+) +$2 +" /etc/mtab </dev/null
> /etc/rcS.d/S12mtab.sh: line 39:   273 Bus error               grep -E
> -sq "^([^ ]+) +$2 +" /etc/mtab </dev/null
> /etc/init.d/rc: line 77:   241 Segmentation fault      $@
> Cleaning up ifupdown....
> /etc/init.d/rc: line 77:   278 Segmentation fault      $@
> Loading kernel module ieee80211_crypt.
> Loading kernel module ieee80211softmac.
> ieee80211: 802.11 data/management/control stack, git-1.1.13
> ieee80211: Copyright (C) 2004-2005 Intel Corporation
> <jketreno at linux.intel.com>
> Loading kernel module ieee80211.
> Loading kernel module bcm43xx.
> bcm43xx driver
> /etc/rcS.d/S20module-init-tools: line 58:   288 Bus
> error               grep '^[^#]' $MODULES_FILE
>        289 Segmentation fault      | while read module args; do
>     [ "$module" ] || continue; load_module "$module" "$args";
> done
> /etc/init.d/rc: line 77:   286 Segmentation fault      $@
> /etc/init.d/rc: line 77:   300 Segmentation fault      $@
> Loading device-mapper support.
> /etc/init.d/rc: line 77:   307 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   315 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /etc/rcS.d/S30checkfs.sh: line 62:   316 Segmentation fault      which
> on_ac_power >/dev/null 2>&1
> Will now check all file systems.
> fsck 1.40-WIP (14-Nov-2006)
> Checking all file systems.
> Done checking file systems.
> A log is being saved in /var/log/fsck/checkfs if that location is
> writable.
> /etc/init.d/rc: line 77:   314 Segmentation fault      $@
> /etc/rcS.d/S30procps.sh: line 22:   322 Segmentation fault      which
> sysctl >/dev/null
> /etc/init.d/rc: line 77:   321 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   330 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> Will now mount local filesystems:.
> Will now activate swapfile swap:done.
> /etc/init.d/rc: line 77:   329 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   343 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /etc/init.d/bootclean: line 169:   344 Segmentation fault      which
> find >/dev/null 2>&1
> /etc/rcS.d/S36mountall-bootclean.sh: line 13:   342 Segmentation
> fault      /etc/init.d/bootclean
> /etc/init.d/rc: line 77:   341 Segmentation fault      $@
> /etc/init.d/rc: line 77:   345 Segmentation fault      $@
> b44: eth0: Link is up at 100 Mbps, full duplex.
> b44: eth0: Flow control is off for TX and off for RX.
> Added VLAN with VID == 1 to IF -:eth0:-
> WARNING:  VLAN 1 does not work with many switches,
> consider another number if you have problems.
> /etc/init.d/rc: line 77:   353 Segmentation fault      $@
> Setting up networking.../etc/init.d/rc: line 77:   367 Segmentation
> fault      $@
> Configuring network interfaces...ifup: failed to open statefile
> /etc/network/run/ifstate: No such file or directory
> /etc/rcS.d/S40networking: line 74:   375 Bus error               ifup -a
> failed.
> /etc/init.d/rc: line 77:   374 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   385 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /etc/init.d/rc: line 77:   384 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   391 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /etc/init.d/bootclean: line 169:   392 Segmentation fault      which
> find >/dev/null 2>&1
> /etc/rcS.d/S46mountnfs-bootclean.sh: line 13:   390 Segmentation
> fault      /etc/init.d/bootclean
> /etc/init.d/rc: line 77:   389 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   397 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /etc/rcS.d/S55bootmisc.sh: line 16:   398 Bus error               grep
> -q ^utmp: /etc/group
> /etc/rcS.d/S55bootmisc.sh: line 16:   401 Segmentation fault    
> which dmesg >/dev/null 2>&1
> /etc/init.d/rc: line 77:   396 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   405 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> Initializing random number generator...done.
> /etc/init.d/rc: line 77:   403 Segmentation fault      $@
> /etc/init.d/rc: line 77:   416 Segmentation fault      $@
> /etc/init.d/rc: line 77:   420 Segmentation fault      $@
> INIT: Entering runlevel: 2
> Starting system log daemon: syslogd/etc/rc2.d/S10sysklogd: line 14: 
> 430 Bus error               chown root:adm /dev/xconsole
> /etc/rc2.d/S10sysklogd: line 58:   431 Segmentation fault    
> start-stop-daemon --start --quiet --exec $binpath -- $SYSLOGD
> .
> /etc/init.d/rc: line 77:   428 Segmentation fault      $@
> Starting kernel log daemon: klogd.
> /etc/init.d/rc: line 77:   436 Segmentation fault      $@
> Zaptel telephony kernel driver: FATAL: Module ztdummy not found.
> Notice: Configuration file is /etc/zaptel.conf
> line 0: Unable to open master device '/dev/zap/ctl'
>
> 1 error(s) detected
>
> /sbin/ztcfg failed. Check /etc/zaptel.confzaptel.
> /etc/init.d/rc: line 77:   442 Segmentation fault      $@
> /etc/init.d/rc: line 77:   449 Segmentation fault      $@
> /etc/init.d/rc: line 77:   450 Segmentation fault      $@
> /etc/rc2.d/S20openbsd-inetd: line 37:   452 Bus error             
> grep -q "^[0-9A-Za-z/]" /etc/inetd.conf
> * Not starting internet superserver: no services enabled.
> /etc/init.d/rc: line 77:   451 Segmentation fault      $@
> /etc/init.d/rc: line 77:   457 Segmentation fault      $@
> /etc/rc2.d/S20ssh: line 7:   459 Segmentation fault      (
> /usr/sbin/sshd -\? 2>&1 | grep -q OpenSSH ) 2>/dev/null
> /etc/init.d/rc: line 77:   458 Segmentation fault      $@
>
>
> Signal 10 (BUS) caught by ps (procps version 3.2.7).
> Please send bug reports to <feedback at lists.sf.net> or
> <albert at users.sf.net>
> Starting Asterisk PBX:
>
> Signal 10 (BUS) caught by ps (procps version 3.2.7).
> Please send bug reports to <feedback at lists.sf.net> or
> <albert at users.sf.net>
> asterisk.
> /etc/init.d/rc: line 77:   477 Segmentation fault      $@
> Starting periodic command scheduler: crond.
> /etc/init.d/rc: line 77:   499 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   510 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> Running local boot scripts (/etc/rc.local)/etc/rc2.d/S99rc.local: line
> 17:   511 Segmentation fault      /etc/rc.local
>  failed!
> /etc/init.d/rc: line 77:   509 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   518 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /etc/init.d/rc: line 77:   517 Segmentation fault      $@
> /lib/init/vars.sh: line 10:   521 Bus error               egrep -qw
> 'quiet' /proc/cmdline
> /etc/rc2.d/S99stop-bootlogd: line 17:   520 Segmentation fault    
> /etc/init.d/bootlogd stop
> /etc/init.d/rc: line 77:   519 Segmentation fault      $@
>
> Debian GNU/Linux 4.0 asus-debian ttyS0
>
> asus-debian login:
>
> ---------------------------------------------------------------------------------------
>
> fail nr2:
> ---------------------------------------------------------------------------------------
> CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
> Build Date: ¤T 12¤ë 14 15:54:18 CST 2005 (root at localhost.localdomain)
> Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
>
> Initializing Arena
> Initializing Devices.
> et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
> rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
> CPU type 0x29006: 264MHz
> Total memory: 33554432 KBytes
>
> Total memory used by CFE:  0x80800000 - 0x8089B590 (636304)
> Initialized Data:          0x80831700 - 0x80833DE0 (9952)
> BSS Area:                  0x80833DE0 - 0x80835590 (6064)
> Local Heap:                0x80835590 - 0x80899590 (409600)
> Stack Area:                0x80899590 - 0x8089B590 (8192)
> Text (code) segment:       0x80800000 - 0x80831700 (202496)
> Boot area (physical):      0x0089C000 - 0x008DC000
> Relocation Factor:         I:00000000 - D:00000000
>
> Device eth0:  hwaddr 00-17-31-DC-05-70, ipaddr 192.168.1.1, mask
> 255.255.255.0
>         gateway not set, nameserver not set
> Null Rescue Flag.
> Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
> Loading: .. 3740 bytes read
> Entry at 0x80001000
> Closing network.
> Starting program at 0x80001000
> Linux version 2.6.19.2 (tch at tomek) (gcc version 4.1.2) #9 Tue Apr 3
> 21:30:54 CEST 2007
> CPU revision is: 00029006
> ssb: Sonics Silicon Backplane found on address 0x18000000
> Determined physical RAM map:
>  memory: 02000000 @ 00000000 (usable)
> Initrd not found or empty - disabling initrd
> Built 1 zonelists.  Total pages: 8128
> Kernel command line: root=/dev/sda1 rootdelay=10 console=ttyS0,115200
> Primary instruction cache 16kB, physically tagged, 2-way, linesize 16
> bytes.
> Primary data cache 16kB, 2-way, linesize 16 bytes.
> Synthesized TLB refill handler (19 instructions).
> Synthesized TLB load handler fastpath (31 instructions).
> Synthesized TLB store handler fastpath (31 instructions).
> Synthesized TLB modify handler fastpath (30 instructions).
> PID hash table entries: 128 (order: 7, 512 bytes)
> Using 132.000 MHz high precision timer.
> Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
> Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
> Memory: 29776k/32768k available (2117k kernel code, 2992k reserved,
> 326k data, 120k init, 0k highmem)
> Mount-cache hash table entries: 512
> Checking for 'wait' instruction...  unavailable.
> NET: Registered protocol family 16
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> PCI: fixing up bridge
> PCI: Fixing up device 0000:00:00.0
> NET: Registered protocol family 2
> IP route cache hash table entries: 256 (order: -2, 1024 bytes)
> TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> TCP bind hash table entries: 512 (order: -1, 2048 bytes)
> TCP: Hash tables configured (established 1024 bind 512)
> TCP reno registered
> JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
> io scheduler noop registered
> io scheduler deadline registered (default)
> Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
> serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
> serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
> b44.c:v1.01 (Jun 16, 2006)
> eth0: Broadcom 10/100BaseT Ethernet 00:17:31:dc:05:70
> eth1: Broadcom 10/100BaseT Ethernet 40:10:18:00:00:2d
> flash init: 0x1c000000 0x02000000
> Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
>  Amd/Fujitsu Extended Query Table at 0x0040
> Physically mapped flash: CFI does not contain boot bank location.
> Assuming top.
> number of CFI chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> Flash device: 0x800000 at 0x1fc00000
> bootloader size: 262144
> Creating 4 MTD partitions on "Physically mapped flash":
> 0x00000000-0x00040000 : "cfe"
> 0x00040000-0x007f0000 : "linux"
> 0x00120000-0x007f0000 : "rootfs"
> 0x007f0000-0x00800000 : "nvram"
> PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
> PCI: Fixing up device 0000:00:03.2
> ehci_hcd 0000:00:03.2: EHCI Host Controller
> ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:03.2: irq 6, io mem 0x40000000
> ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 4 ports detected
> USB Universal Host Controller Interface driver v3.0
> PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.0
> uhci_hcd 0000:00:03.0: UHCI Host Controller
> uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.1
> uhci_hcd 0000:00:03.1: UHCI Host Controller
> uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> usb 1-2: new high speed USB device using ehci_hcd and address 2
> Initializing USB Mass Storage driver...
> usb 1-2: configuration #1 chosen from 1 choice
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> ip_conntrack version 2.4 (256 buckets, 2048 max) - 240 bytes per conntrack
> ip_tables: (C) 2000-2006 Netfilter Core Team
> TCP cubic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> 802.1Q VLAN Support v1.8 Ben Greear <greearb at candelatech.com>
> All bugs added by David S. Miller <davem at redhat.com>
> Waiting 10sec before mounting root device...
> Time: MIPS clocksource has been installed.
> scsi 0:0:0:0: Direct-Access     TOSHIBA  MK1016GAP        U1.1 PQ: 0
> ANSI: 0 CCS
> SCSI device sda: 19640880 512-byte hdwr sectors (10056 MB)
> sda: Write Protect is off
> sda: assuming drive cache: write through
> SCSI device sda: 19640880 512-byte hdwr sectors (10056 MB)
> sda: Write Protect is off
> sda: assuming drive cache: write through
>  sda: sda1 sda2
> sd 0:0:0:0: Attached scsi disk sda
> EXT3-fs: INFO: recovery required on readonly filesystem.
> EXT3-fs: write access will be enabled during recovery.
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 120k freed
> Algorithmics/MIPS FPU Emulator v1.5
> INIT: version 2.86 booting
> /etc/init.d/rc: line 77:   133 Bus error               $@
> /etc/init.d/rc: line 77:   149 Bus error               $@
> /etc/init.d/rc: line 77:   152 Bus error               $@
> /etc/rcS.d/S03udev: line 60:   187 Done                    grep
> '^[^#]' /etc/udev/links.conf
>        188 Bus error               | while read type name arg1; do
>     [ "$type" -a "$name" -a ! -e "/dev/$name" -a ! -L "/dev/$name" ]
> || continue; case "$type" in
>         L)
>             ln -s $arg1 /dev/$name
>         ;;
>         D)
>             mkdir -p /dev/$name
>         ;;
>         M)
>             mknod -m 600 /dev/$name $arg1
>         ;;
>         *)
>             log_warning_msg "links.conf: unparseable line ($type $name
> $arg1)"
>         ;;
>     esac; if [ -x /sbin/restorecon ]; then
>         /sbin/restorecon /dev/$name >/dev/null 2>/dev/null;
>     fi;
> done
> /etc/init.d/rc: line 77:   175 Bus error               $@
> /etc/init.d/rc: line 77:   207 Bus error               $@
> /etc/init.d/rc: line 77:   220 Bus error               $@
> /etc/rcS.d/S10checkroot.sh: line 24:   229 Bus error               ( [
> "$PASS" != 0 ] && [ "$PASS" != "" ] )
> /etc/rcS.d/S10checkroot.sh: line 24:   230 Bus error               ( [
> "$FSTYPE" = "nfs" ] || [ "$FSTYPE" = "nfs4" ] )
> Activating swap:.
> /etc/rcS.d/S10checkroot.sh: line 24:   236 Bus error             
> which on_ac_power >/dev/null 2>&1
> EXT3 FS on sda1, internal journal
> /etc/init.d/rc: line 77:   225 Bus error               $@
> Setting the system clock..
> Cannot access the Hardware Clock via any known method.
> Use the --debug option to see the details of our search for an access
> method.
> System Clock set. Local time: Sat Jan  1 00:00:19 UTC 2000.
> /etc/init.d/rc: line 77:   247 Bus error               $@
> /lib/init/mount-functions.sh: line 23:   258 Bus error             
> which selinuxenabled >/dev/null 2>&1
> /etc/init.d/rc: line 77:   253 Bus error               $@
> Cleaning up ifupdown....
> /etc/init.d/rc: line 77:   302 Bus error               $@
> Loading kernel module ieee80211_crypt.
> Loading kernel module ieee80211softmac.
> ieee80211: 802.11 data/management/control stack, git-1.1.13
> ieee80211: Copyright (C) 2004-2005 Intel Corporation
> <jketreno at linux.intel.com>
> Loading kernel module ieee80211.
> Loading kernel module bcm43xx.
> bcm43xx driver
> /etc/rcS.d/S20module-init-tools: line 58:   312
> Done                    grep '^[^#]' $MODULES_FILE
>        313 Bus error               | while read module args; do
>     [ "$module" ] || continue; load_module "$module" "$args";
> done
> /etc/init.d/rc: line 77:   310 Bus error               $@
> /etc/init.d/rc: line 77:   319 Bus error               $@
> Loading device-mapper support.
> /etc/init.d/rc: line 77:   326 Bus error               $@
> /etc/rcS.d/S30checkfs.sh: line 62:   335 Bus error               which
> on_ac_power >/dev/null 2>&1
> Will now check all file systems.
> fsck 1.40-WIP (14-Nov-2006)
> Checking all file systems.
> Done checking file systems.
> A log is being saved in /var/log/fsck/checkfs if that location is
> writable.
> /etc/init.d/rc: line 77:   333 Bus error               $@
> /etc/rcS.d/S30procps.sh: line 22:   341 Bus error               which
> sysctl >/dev/null
> /etc/init.d/rc: line 77:   340 Bus error               $@
> Will now mount local filesystems:.
> Will now activate swapfile swap:done.
> /etc/init.d/rc: line 77:   348 Bus error               $@
> /etc/init.d/bootclean: line 169:   363 Bus error               which
> find >/dev/null 2>&1
> /etc/rcS.d/S36mountall-bootclean.sh: line 13:   361 Bus
> error               /etc/init.d/bootclean
> /etc/init.d/rc: line 77:   360 Bus error               $@
> /etc/init.d/rc: line 77:   364 Bus error               $@
> b44: eth0: Link is up at 100 Mbps, full duplex.
> b44: eth0: Flow control is off for TX and off for RX.
> /etc/rcS.d/S38vlans: line 4:   374 Bus error               ifconfig
> eth0 0.0.0.0
> Added VLAN with VID == 1 to IF -:eth0:-
> WARNING:  VLAN 1 does not work with many switches,
> consider another number if you have problems.
> /etc/init.d/rc: line 77:   373 Bus error               $@
> Setting up networking.../etc/init.d/rc: line 77:   386 Bus
> error               $@
> Configuring network interfaces...ifup: failed to open statefile
> /etc/network/run/ifstate: No such file or directory
> /etc/rcS.d/S40networking: line 74:   394 Bus error               ifup -a
> failed.
> /etc/init.d/rc: line 77:   393 Bus error               $@
> /etc/init.d/rc: line 77:   403 Bus error               $@
> /etc/init.d/bootclean: line 169:   411 Bus error               which
> find >/dev/null 2>&1
> /etc/rcS.d/S46mountnfs-bootclean.sh: line 13:   409 Bus
> error               /etc/init.d/bootclean
> /etc/init.d/rc: line 77:   408 Bus error               $@
> /etc/rcS.d/S55bootmisc.sh: line 16:   419 Bus error             
> chgrp utmp /var/run/utmp
> /etc/rcS.d/S55bootmisc.sh: line 16:   422 Bus error             
> which dmesg >/dev/null 2>&1
> /etc/init.d/rc: line 77:   415 Bus error               $@
> /etc/init.d/rc: line 77:   424 Bus error               $@
> /etc/init.d/rc: line 77:   431 Bus error               $@
> /etc/init.d/rc: line 77:   435 Bus error               $@
> INIT: Entering runlevel: 2
> Starting system log daemon: syslogd/etc/rc2.d/S10sysklogd: line 14: 
> 445 Bus error               chown root:adm /dev/xconsole
> .
> /etc/init.d/rc: line 77:   443 Bus error               $@
> Starting kernel log daemon: klogd.
> /etc/init.d/rc: line 77:   451 Bus error               $@
> Zaptel telephony kernel driver: FATAL: Module ztdummy not found.
> Notice: Configuration file is /etc/zaptel.conf
> line 0: Unable to open master device '/dev/zap/ctl'
>
> 1 error(s) detected
>
> /etc/rc2.d/S15zaptel: line 120:   460 Bus error               $DAEMON
> $DAEMON_OPTS
> /sbin/ztcfg failed. Check /etc/zaptel.confzaptel.
> /etc/init.d/rc: line 77:   457 Bus error               $@
> /etc/init.d/rc: line 77:   464 Bus error               $@
> /etc/init.d/rc: line 77:   465 Bus error               $@
> * Not starting internet superserver: no services enabled.
> /etc/init.d/rc: line 77:   467 Bus error               $@
> /etc/init.d/rc: line 77:   473 Bus error               $@
> /etc/rc2.d/S20ssh: line 7:   475 Bus error               (
> /usr/sbin/sshd -\? 2>&1 | grep -q OpenSSH ) 2>/dev/null
> /etc/init.d/rc: line 77:   474 Bus error               $@
>
>
> Signal 10 (BUS) caught by ps (procps version 3.2.7).
> Please send bug reports to <feedback at lists.sf.net> or
> <albert at users.sf.net>
> awk: cmd. line:1: fatal error: internal error
> Starting Asterisk PBX:
>
> Signal 10 (BUS) caught by ps (procps version 3.2.7).
> Please send bug reports to <feedback at lists.sf.net> or
> <albert at users.sf.net>
> awk: cmd. line:1: fatal error: internal error
> asterisk.
> /etc/init.d/rc: line 77:   493 Bus error               $@
> Jan  1 01:00:38 WARNING[508]: manager.c:1743 init_manager: Unable to
> bind socket: Cannot assign requested address
> Starting periodic command scheduler: crond.
> /etc/init.d/rc: line 77:   515 Bus error               $@
> Running local boot scripts (/etc/rc.local)/etc/rc2.d/S99rc.local: line
> 17:   527 Bus error               /etc/rc.local
>  failed!
> /etc/init.d/rc: line 77:   525 Bus error               $@
> /etc/init.d/rc: line 77:   533 Bus error               $@
> /etc/rc2.d/S99stop-bootlogd: line 17:   536 Bus error             
> /etc/init.d/bootlogd stop
> /etc/init.d/rc: line 77:   535 Bus error               $@
> ---------------------------------------------------------------------------------------
>
> successful boot
> ---------------------------------------------------------------------------------------
>
> CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
> Build Date: ¤T 12¤ë 14 15:54:18 CST 2005 (root at localhost.localdomain)
> Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
>
> Initializing Arena
> Initializing Devices.
> et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
> rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
> CPU type 0x29006: 264MHz
> Total memory: 33554432 KBytes
>
> Total memory used by CFE:  0x80800000 - 0x8089B590 (636304)
> Initialized Data:          0x80831700 - 0x80833DE0 (9952)
> BSS Area:                  0x80833DE0 - 0x80835590 (6064)
> Local Heap:                0x80835590 - 0x80899590 (409600)
> Stack Area:                0x80899590 - 0x8089B590 (8192)
> Text (code) segment:       0x80800000 - 0x80831700 (202496)
> Boot area (physical):      0x0089C000 - 0x008DC000
> Relocation Factor:         I:00000000 - D:00000000
>
> Device eth0:  hwaddr 00-17-31-DC-05-70, ipaddr 192.168.1.1, mask
> 255.255.255.0
>         gateway not set, nameserver not set
> Null Rescue Flag.
> Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
> Loading: .. 3740 bytes read
> Entry at 0x80001000
> Closing network.
> Starting program at 0x80001000
> Linux version 2.6.19.2 (tch at tomek) (gcc version 4.1.2) #9 Tue Apr 3
> 21:30:54 CEST 2007
> CPU revision is: 00029006
> ssb: Sonics Silicon Backplane found on address 0x18000000
> Determined physical RAM map:
>  memory: 02000000 @ 00000000 (usable)
> Initrd not found or empty - disabling initrd
> Built 1 zonelists.  Total pages: 8128
> Kernel command line: root=/dev/sda1 rootdelay=10 console=ttyS0,115200
> Primary instruction cache 16kB, physically tagged, 2-way, linesize 16
> bytes.
> Primary data cache 16kB, 2-way, linesize 16 bytes.
> Synthesized TLB refill handler (19 instructions).
> Synthesized TLB load handler fastpath (31 instructions).
> Synthesized TLB store handler fastpath (31 instructions).
> Synthesized TLB modify handler fastpath (30 instructions).
> PID hash table entries: 128 (order: 7, 512 bytes)
> Using 132.000 MHz high precision timer.
> Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
> Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
> Memory: 29776k/32768k available (2117k kernel code, 2992k reserved,
> 326k data, 120k init, 0k highmem)
> Mount-cache hash table entries: 512
> Checking for 'wait' instruction...  unavailable.
> NET: Registered protocol family 16
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> PCI: fixing up bridge
> PCI: Fixing up device 0000:00:00.0
> NET: Registered protocol family 2
> IP route cache hash table entries: 256 (order: -2, 1024 bytes)
> TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> TCP bind hash table entries: 512 (order: -1, 2048 bytes)
> TCP: Hash tables configured (established 1024 bind 512)
> TCP reno registered
> JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
> io scheduler noop registered
> io scheduler deadline registered (default)
> Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
> serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
> serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
> b44.c:v1.01 (Jun 16, 2006)
> eth0: Broadcom 10/100BaseT Ethernet 00:17:31:dc:05:70
> eth1: Broadcom 10/100BaseT Ethernet 40:10:18:00:00:2d
> flash init: 0x1c000000 0x02000000
> Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
>  Amd/Fujitsu Extended Query Table at 0x0040
> Physically mapped flash: CFI does not contain boot bank location.
> Assuming top.
> number of CFI chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> Flash device: 0x800000 at 0x1fc00000
> bootloader size: 262144
> Creating 4 MTD partitions on "Physically mapped flash":
> 0x00000000-0x00040000 : "cfe"
> 0x00040000-0x007f0000 : "linux"
> 0x00120000-0x007f0000 : "rootfs"
> 0x007f0000-0x00800000 : "nvram"
> PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
> PCI: Fixing up device 0000:00:03.2
> ehci_hcd 0000:00:03.2: EHCI Host Controller
> ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:03.2: irq 6, io mem 0x40000000
> ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 4 ports detected
> USB Universal Host Controller Interface driver v3.0
> PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.0
> uhci_hcd 0000:00:03.0: UHCI Host Controller
> uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.1
> uhci_hcd 0000:00:03.1: UHCI Host Controller
> uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> usb 1-2: new high speed USB device using ehci_hcd and address 2
> Initializing USB Mass Storage driver...
> usb 1-2: configuration #1 chosen from 1 choice
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> ip_conntrack version 2.4 (256 buckets, 2048 max) - 240 bytes per conntrack
> ip_tables: (C) 2000-2006 Netfilter Core Team
> TCP cubic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> 802.1Q VLAN Support v1.8 Ben Greear <greearb at candelatech.com>
> All bugs added by David S. Miller <davem at redhat.com>
> Waiting 10sec before mounting root device...
> Time: MIPS clocksource has been installed.
> scsi 0:0:0:0: Direct-Access     TOSHIBA  MK1016GAP        U1.1 PQ: 0
> ANSI: 0 CCS
> SCSI device sda: 19640880 512-byte hdwr sectors (10056 MB)
> sda: Write Protect is off
> sda: assuming drive cache: write through
> SCSI device sda: 19640880 512-byte hdwr sectors (10056 MB)
> sda: Write Protect is off
> sda: assuming drive cache: write through
>  sda: sda1 sda2
> sd 0:0:0:0: Attached scsi disk sda
> EXT3-fs: INFO: recovery required on readonly filesystem.
> EXT3-fs: write access will be enabled during recovery.
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 120k freed
> Algorithmics/MIPS FPU Emulator v1.5
> INIT: version 2.86 booting
> Starting the hotplug events dispatcher: udevd.
> Synthesizing the initial hotplug events...done.
> Waiting for /dev to be fully populated...ieee80211: 802.11
> data/management/control stack, git-1.1.13
> ieee80211: Copyright (C) 2004-2005 Intel Corporation
> <jketreno at linux.intel.com>
> bcm43xx driver
> done.
> Activating swap:.
> Will now check root file system:fsck 1.40-WIP (14-Nov-2006)
> [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/sda1
> /dev/sda1: clean, 15866/1177344 files, 200094/2351152 blocks
> .
> EXT3 FS on sda1, internal journal
> Setting the system clock..
> Cannot access the Hardware Clock via any known method.
> Use the --debug option to see the details of our search for an access
> method.
> System Clock set. Local time: Sat Jan  1 00:00:23 UTC 2000.
> Cleaning up ifupdown....
> Loading kernel module ieee80211_crypt.
> Loading kernel module ieee80211softmac.
> Loading kernel module ieee80211.
> Loading kernel module bcm43xx.
> Loading device-mapper support.
> Will now check all file systems.
> fsck 1.40-WIP (14-Nov-2006)
> Checking all file systems.
> Done checking file systems.
> A log is being saved in /var/log/fsck/checkfs if that location is
> writable.
> Setting kernel variables...done.
> Will now mount local filesystems:.
> Will now activate swapfile swap:done.
> Cleaning /tmp...done.
> Cleaning /var/run...done.
> Cleaning /var/lock...done.
> b44: eth0: Link is up at 100 Mbps, full duplex.
> b44: eth0: Flow control is off for TX and off for RX.
> Added VLAN with VID == 1 to IF -:eth0:-
> WARNING:  VLAN 1 does not work with many switches,
> consider another number if you have problems.
> Setting up networking....
> Configuring network interfaces...done.
> Initializing random number generator...done.
> INIT: Entering runlevel: 2
> Starting system log daemon: syslogd.
> Starting kernel log daemon: klogd.
> Zaptel telephony kernel driver: FATAL: Module ztdummy not found.
> Notice: Configuration file is /etc/zaptel.conf
> line 0: Unable to open master device '/dev/zap/ctl'
>
> 1 error(s) detected
>
> /sbin/ztcfg failed. Check /etc/zaptel.confzaptel.
> * Not starting internet superserver: no services enabled.
> Starting OpenBSD Secure Shell server: sshd.
> Starting Asterisk PBX: asterisk.
> Starting periodic command scheduler: crond.
> Running local boot scripts (/etc/rc.local).
>
> Debian GNU/Linux 4.0 asus-debian ttyS0
>
> asus-debian login:
>
>
>
>   



More information about the debian-non-standard mailing list